STM32F4 rešitve
// STM32F4 Discovery - Assembly template for CO LAB course
//
// Based on: https://github.com/fcayci/stm32f4-assembly
//
// Turns on an LED attached to GPIOD Pin 12
// We need to enable the clock for GPIOD and set up pin 12 as output.
//
// We also measure delay by using SysTick Timer, coresponding code is included
//
// Start with enabling thumb 32 mode since Cortex-M4 do not work with arm mode
// Unified syntax is used to enable good of the both words...
// Make sure to run arm-none-eabi-objdump.exe -d prj1.elf to check if
// the assembler used proper instructions. (Like ADDS)
.thumb
.syntax unified
.cpu cortex-m4
//.arch armv7e-m
///////////////////////////////////////////////////////////////////////////////
// Definitions
///////////////////////////////////////////////////////////////////////////////
// Definitions section. Define all the registers and
// constants here for code readability.
// Constants
.equ LEDDELAY, 4000
// By default 16MHz internal HSI clock is enabled
// Internal loop takes 4 cycles
// Register Addresses
// You can find the base addresses for all peripherals from Memory Map section
// RM0090 on page 64. Then the offsets can be found on their relevant sections.
// RCC base address is 0x40023800
// AHB1ENR register offset is 0x30
.equ RCC_AHB1ENR, 0x40023830 // RCC AHB1 peripheral clock reg (page 180)
// GPIOD base address is 0x40020C00
.equ GPIOD_BASE, 0x40020C00 // GPIOD base address)
// MODER register offset is 0x00
.equ GPIOD_MODER, 0x00 // GPIOD port mode register (page 281)
// ODR register offset is 0x14
.equ GPIOD_ODR, 0x14 // GPIOD output data register (page 283)
// BSSR register offset is 0x18
.equ GPIOD_BSSR, 0x18 // GPIOD port set/reset register (page 284)
//Absolute addresses
// .equ GPIOD_MODER, 0x40020C00 // GPIOD port mode register (page 281)
// .equ GPIOD_ODR, 0x40020C14 // GPIOD output data register (page 283)
// .equ GPIOD_BSSR, 0x40020C18 // GPIOD port set/reset register (page 284)
// SysTick Timer definitions
.equ SCS, 0xe000e000
.equ SCS_SYST_CSR, 0x10 // Control/Status register
.equ SCS_SYST_RVR, 0x14 // Value to countdown from
.equ SCS_SYST_CVR, 0x18 // Current value
.equ SYSTICK_RELOAD_1MS, 15999 //1 msec at 16MHz ... 16 000 000 / 500 - 1
// Values for BSSR register - pin 12
.equ LEDs_ON, 0x0000F000
.equ LEDs_OFF, 0xF0000000
@ -- Zero initialized data ---
.section .data
LEDSTAT: .word 0
// Start of text section
.section .text
///////////////////////////////////////////////////////////////////////////////
// Vectors
///////////////////////////////////////////////////////////////////////////////
// Vector table start
// Add all other processor specific exceptions/interrupts in order here
.long __StackTop // Top of the stack. from linker script
.long _start +1 // reset location, +1 for thumb mode
.word NMI_Handler
.word HardFault_Handler
.word MemManage_Handler
.word BusFault_Handler
.word UsageFault_Handler
.word 0
.word 0
.word 0
.word 0
.word SVC_Handler
.word DebugMon_Handler
.word 0
.word PendSV_Handler
.word SysTick_Handler
/* External Interrupts */
.word WWDG_IRQHandler /* Window WatchDog */
.word PVD_IRQHandler /* PVD through EXTI Line detection */
.word TAMP_STAMP_IRQHandler /* Tamper and TimeStamps through the EXTI line */
.word RTC_WKUP_IRQHandler /* RTC Wakeup through the EXTI line */
.word FLASH_IRQHandler /* FLASH */
.word RCC_IRQHandler /* RCC */
.word EXTI0_IRQHandler /* EXTI Line0 */
.word EXTI1_IRQHandler /* EXTI Line1 */
.word EXTI2_IRQHandler /* EXTI Line2 */
.word EXTI3_IRQHandler /* EXTI Line3 */
.word EXTI4_IRQHandler /* EXTI Line4 */
.word DMA1_Stream0_IRQHandler /* DMA1 Stream 0 */
.word DMA1_Stream1_IRQHandler /* DMA1 Stream 1 */
.word DMA1_Stream2_IRQHandler /* DMA1 Stream 2 */
.word DMA1_Stream3_IRQHandler /* DMA1 Stream 3 */
.word DMA1_Stream4_IRQHandler /* DMA1 Stream 4 */
.word DMA1_Stream5_IRQHandler /* DMA1 Stream 5 */
.word DMA1_Stream6_IRQHandler /* DMA1 Stream 6 */
.word ADC_IRQHandler /* ADC1, ADC2 and ADC3s */
.word CAN1_TX_IRQHandler /* CAN1 TX */
.word CAN1_RX0_IRQHandler /* CAN1 RX0 */
.word CAN1_RX1_IRQHandler /* CAN1 RX1 */
.word CAN1_SCE_IRQHandler /* CAN1 SCE */
.word EXTI9_5_IRQHandler /* External Line[9:5]s */
.word TIM1_BRK_TIM9_IRQHandler /* TIM1 Break and TIM9 */
.word TIM1_UP_TIM10_IRQHandler /* TIM1 Update and TIM10 */
.word TIM1_TRG_COM_TIM11_IRQHandler /* TIM1 Trigger and Commutation and TIM11 */
.word TIM1_CC_IRQHandler /* TIM1 Capture Compare */
.word TIM2_IRQHandler /* TIM2 */
.word TIM3_IRQHandler /* TIM3 */
.word TIM4_IRQHandler /* TIM4 */
.word I2C1_EV_IRQHandler /* I2C1 Event */
.word I2C1_ER_IRQHandler /* I2C1 Error */
.word I2C2_EV_IRQHandler /* I2C2 Event */
.word I2C2_ER_IRQHandler /* I2C2 Error */
.word SPI1_IRQHandler /* SPI1 */
.word SPI2_IRQHandler /* SPI2 */
.word USART1_IRQHandler /* USART1 */
.word USART2_IRQHandler /* USART2 */
.word USART3_IRQHandler /* USART3 */
.word EXTI15_10_IRQHandler /* External Line[15:10]s */
.word RTC_Alarm_IRQHandler /* RTC Alarm (A and B) through EXTI Line */
.word OTG_FS_WKUP_IRQHandler /* USB OTG FS Wakeup through EXTI line */
.word TIM8_BRK_TIM12_IRQHandler /* TIM8 Break and TIM12 */
.word TIM8_UP_TIM13_IRQHandler /* TIM8 Update and TIM13 */
.word TIM8_TRG_COM_TIM14_IRQHandler /* TIM8 Trigger and Commutation and TIM14 */
.word TIM8_CC_IRQHandler /* TIM8 Capture Compare */
.word DMA1_Stream7_IRQHandler /* DMA1 Stream7 */
.word FSMC_IRQHandler /* FSMC */
.word SDIO_IRQHandler /* SDIO */
.word TIM5_IRQHandler /* TIM5 */
.word SPI3_IRQHandler /* SPI3 */
.word UART4_IRQHandler /* UART4 */
.word UART5_IRQHandler /* UART5 */
.word TIM6_DAC_IRQHandler /* TIM6 and DAC1&2 underrun errors */
.word TIM7_IRQHandler /* TIM7 */
.word DMA2_Stream0_IRQHandler /* DMA2 Stream 0 */
.word DMA2_Stream1_IRQHandler /* DMA2 Stream 1 */
.word DMA2_Stream2_IRQHandler /* DMA2 Stream 2 */
.word DMA2_Stream3_IRQHandler /* DMA2 Stream 3 */
.word DMA2_Stream4_IRQHandler /* DMA2 Stream 4 */
.word ETH_IRQHandler /* Ethernet */
.word ETH_WKUP_IRQHandler /* Ethernet Wakeup through EXTI line */
.word CAN2_TX_IRQHandler /* CAN2 TX */
.word CAN2_RX0_IRQHandler /* CAN2 RX0 */
.word CAN2_RX1_IRQHandler /* CAN2 RX1 */
.word CAN2_SCE_IRQHandler /* CAN2 SCE */
.word OTG_FS_IRQHandler /* USB OTG FS */
.word DMA2_Stream5_IRQHandler /* DMA2 Stream 5 */
.word DMA2_Stream6_IRQHandler /* DMA2 Stream 6 */
.word DMA2_Stream7_IRQHandler /* DMA2 Stream 7 */
.word USART6_IRQHandler /* USART6 */
.word I2C3_EV_IRQHandler /* I2C3 event */
.word I2C3_ER_IRQHandler /* I2C3 error */
.word OTG_HS_EP1_OUT_IRQHandler /* USB OTG HS End Point 1 Out */
.word OTG_HS_EP1_IN_IRQHandler /* USB OTG HS End Point 1 In */
.word OTG_HS_WKUP_IRQHandler /* USB OTG HS Wakeup through EXTI */
.word OTG_HS_IRQHandler /* USB OTG HS */
.word DCMI_IRQHandler /* DCMI */
.word 0 /* CRYP crypto */
.word HASH_RNG_IRQHandler /* Hash and Rng */
.word FPU_IRQHandler /* FPU */
/*******************************************************************************
*
* Provide weak aliases for each Exception handler to the Default_Handler.
* As they are weak aliases, any function with the same name will override
* this definition.
*
*******************************************************************************/
.weak NMI_Handler
.thumb_set NMI_Handler,Default_Handler
.weak HardFault_Handler
.thumb_set HardFault_Handler,Default_Handler
.weak MemManage_Handler
.thumb_set MemManage_Handler,Default_Handler
.weak BusFault_Handler
.thumb_set BusFault_Handler,Default_Handler
.weak UsageFault_Handler
.thumb_set UsageFault_Handler,Default_Handler
.weak SVC_Handler
.thumb_set SVC_Handler,Default_Handler
.weak DebugMon_Handler
.thumb_set DebugMon_Handler,Default_Handler
.weak PendSV_Handler
.thumb_set PendSV_Handler,Default_Handler
.weak SysTick_Handler
// .thumb_set SysTick_Handler,Default_Handler
.weak WWDG_IRQHandler
.thumb_set WWDG_IRQHandler,Default_Handler
.weak PVD_IRQHandler
.thumb_set PVD_IRQHandler,Default_Handler
.weak TAMP_STAMP_IRQHandler
.thumb_set TAMP_STAMP_IRQHandler,Default_Handler
.weak RTC_WKUP_IRQHandler
.thumb_set RTC_WKUP_IRQHandler,Default_Handler
.weak FLASH_IRQHandler
.thumb_set FLASH_IRQHandler,Default_Handler
.weak RCC_IRQHandler
.thumb_set RCC_IRQHandler,Default_Handler
.weak EXTI0_IRQHandler
.thumb_set EXTI0_IRQHandler,Default_Handler
.weak EXTI1_IRQHandler
.thumb_set EXTI1_IRQHandler,Default_Handler
.weak EXTI2_IRQHandler
.thumb_set EXTI2_IRQHandler,Default_Handler
.weak EXTI3_IRQHandler
.thumb_set EXTI3_IRQHandler,Default_Handler
.weak EXTI4_IRQHandler
.thumb_set EXTI4_IRQHandler,Default_Handler
.weak DMA1_Stream0_IRQHandler
.thumb_set DMA1_Stream0_IRQHandler,Default_Handler
.weak DMA1_Stream1_IRQHandler
.thumb_set DMA1_Stream1_IRQHandler,Default_Handler
.weak DMA1_Stream2_IRQHandler
.thumb_set DMA1_Stream2_IRQHandler,Default_Handler
.weak DMA1_Stream3_IRQHandler
.thumb_set DMA1_Stream3_IRQHandler,Default_Handler
.weak DMA1_Stream4_IRQHandler
.thumb_set DMA1_Stream4_IRQHandler,Default_Handler
.weak DMA1_Stream5_IRQHandler
.thumb_set DMA1_Stream5_IRQHandler,Default_Handler
.weak DMA1_Stream6_IRQHandler
.thumb_set DMA1_Stream6_IRQHandler,Default_Handler
.weak ADC_IRQHandler
.thumb_set ADC_IRQHandler,Default_Handler
.weak CAN1_TX_IRQHandler
.thumb_set CAN1_TX_IRQHandler,Default_Handler
.weak CAN1_RX0_IRQHandler
.thumb_set CAN1_RX0_IRQHandler,Default_Handler
.weak CAN1_RX1_IRQHandler
.thumb_set CAN1_RX1_IRQHandler,Default_Handler
.weak CAN1_SCE_IRQHandler
.thumb_set CAN1_SCE_IRQHandler,Default_Handler
.weak EXTI9_5_IRQHandler
.thumb_set EXTI9_5_IRQHandler,Default_Handler
.weak TIM1_BRK_TIM9_IRQHandler
.thumb_set TIM1_BRK_TIM9_IRQHandler,Default_Handler
.weak TIM1_UP_TIM10_IRQHandler
.thumb_set TIM1_UP_TIM10_IRQHandler,Default_Handler
.weak TIM1_TRG_COM_TIM11_IRQHandler
.thumb_set TIM1_TRG_COM_TIM11_IRQHandler,Default_Handler
.weak TIM1_CC_IRQHandler
.thumb_set TIM1_CC_IRQHandler,Default_Handler
.weak TIM2_IRQHandler
.thumb_set TIM2_IRQHandler,Default_Handler
.weak TIM3_IRQHandler
.thumb_set TIM3_IRQHandler,Default_Handler
.weak TIM4_IRQHandler
.thumb_set TIM4_IRQHandler,Default_Handler
.weak I2C1_EV_IRQHandler
.thumb_set I2C1_EV_IRQHandler,Default_Handler
.weak I2C1_ER_IRQHandler
.thumb_set I2C1_ER_IRQHandler,Default_Handler
.weak I2C2_EV_IRQHandler
.thumb_set I2C2_EV_IRQHandler,Default_Handler
.weak I2C2_ER_IRQHandler
.thumb_set I2C2_ER_IRQHandler,Default_Handler
.weak SPI1_IRQHandler
.thumb_set SPI1_IRQHandler,Default_Handler
.weak SPI2_IRQHandler
.thumb_set SPI2_IRQHandler,Default_Handler
.weak USART1_IRQHandler
.thumb_set USART1_IRQHandler,Default_Handler
.weak USART2_IRQHandler
.thumb_set USART2_IRQHandler,Default_Handler
.weak USART3_IRQHandler
.thumb_set USART3_IRQHandler,Default_Handler
.weak EXTI15_10_IRQHandler
.thumb_set EXTI15_10_IRQHandler,Default_Handler
.weak RTC_Alarm_IRQHandler
.thumb_set RTC_Alarm_IRQHandler,Default_Handler
.weak OTG_FS_WKUP_IRQHandler
.thumb_set OTG_FS_WKUP_IRQHandler,Default_Handler
.weak TIM8_BRK_TIM12_IRQHandler
.thumb_set TIM8_BRK_TIM12_IRQHandler,Default_Handler
.weak TIM8_UP_TIM13_IRQHandler
.thumb_set TIM8_UP_TIM13_IRQHandler,Default_Handler
.weak TIM8_TRG_COM_TIM14_IRQHandler
.thumb_set TIM8_TRG_COM_TIM14_IRQHandler,Default_Handler
.weak TIM8_CC_IRQHandler
.thumb_set TIM8_CC_IRQHandler,Default_Handler
.weak DMA1_Stream7_IRQHandler
.thumb_set DMA1_Stream7_IRQHandler,Default_Handler
.weak FSMC_IRQHandler
.thumb_set FSMC_IRQHandler,Default_Handler
.weak SDIO_IRQHandler
.thumb_set SDIO_IRQHandler,Default_Handler
.weak TIM5_IRQHandler
.thumb_set TIM5_IRQHandler,Default_Handler
.weak SPI3_IRQHandler
.thumb_set SPI3_IRQHandler,Default_Handler
.weak UART4_IRQHandler
.thumb_set UART4_IRQHandler,Default_Handler
.weak UART5_IRQHandler
.thumb_set UART5_IRQHandler,Default_Handler
.weak TIM6_DAC_IRQHandler
.thumb_set TIM6_DAC_IRQHandler,Default_Handler
.weak TIM7_IRQHandler
.thumb_set TIM7_IRQHandler,Default_Handler
.weak DMA2_Stream0_IRQHandler
.thumb_set DMA2_Stream0_IRQHandler,Default_Handler
.weak DMA2_Stream1_IRQHandler
.thumb_set DMA2_Stream1_IRQHandler,Default_Handler
.weak DMA2_Stream2_IRQHandler
.thumb_set DMA2_Stream2_IRQHandler,Default_Handler
.weak DMA2_Stream3_IRQHandler
.thumb_set DMA2_Stream3_IRQHandler,Default_Handler
.weak DMA2_Stream4_IRQHandler
.thumb_set DMA2_Stream4_IRQHandler,Default_Handler
.weak ETH_IRQHandler
.thumb_set ETH_IRQHandler,Default_Handler
.weak ETH_WKUP_IRQHandler
.thumb_set ETH_WKUP_IRQHandler,Default_Handler
.weak CAN2_TX_IRQHandler
.thumb_set CAN2_TX_IRQHandler,Default_Handler
.weak CAN2_RX0_IRQHandler
.thumb_set CAN2_RX0_IRQHandler,Default_Handler
.weak CAN2_RX1_IRQHandler
.thumb_set CAN2_RX1_IRQHandler,Default_Handler
.weak CAN2_SCE_IRQHandler
.thumb_set CAN2_SCE_IRQHandler,Default_Handler
.weak OTG_FS_IRQHandler
.thumb_set OTG_FS_IRQHandler,Default_Handler
.weak DMA2_Stream5_IRQHandler
.thumb_set DMA2_Stream5_IRQHandler,Default_Handler
.weak DMA2_Stream6_IRQHandler
.thumb_set DMA2_Stream6_IRQHandler,Default_Handler
.weak DMA2_Stream7_IRQHandler
.thumb_set DMA2_Stream7_IRQHandler,Default_Handler
.weak USART6_IRQHandler
.thumb_set USART6_IRQHandler,Default_Handler
.weak I2C3_EV_IRQHandler
.thumb_set I2C3_EV_IRQHandler,Default_Handler
.weak I2C3_ER_IRQHandler
.thumb_set I2C3_ER_IRQHandler,Default_Handler
.weak OTG_HS_EP1_OUT_IRQHandler
.thumb_set OTG_HS_EP1_OUT_IRQHandler,Default_Handler
.weak OTG_HS_EP1_IN_IRQHandler
.thumb_set OTG_HS_EP1_IN_IRQHandler,Default_Handler
.weak OTG_HS_WKUP_IRQHandler
.thumb_set OTG_HS_WKUP_IRQHandler,Default_Handler
.weak OTG_HS_IRQHandler
.thumb_set OTG_HS_IRQHandler,Default_Handler
.weak DCMI_IRQHandler
.thumb_set DCMI_IRQHandler,Default_Handler
.weak HASH_RNG_IRQHandler
.thumb_set HASH_RNG_IRQHandler,Default_Handler
.weak FPU_IRQHandler
.thumb_set FPU_IRQHandler,Default_Handler
///////////////////////////////////////////////////////////////////////////////
// Main code starts from here
///////////////////////////////////////////////////////////////////////////////
_start:
bl INIT_IO
mov r8,#0 // Clear ms counter
bl INIT_TC_PSP
loop:
// bl LED_ON
// mov r0, 500
// bl DELAYTC
// bl LED_OFF
// mov r0, 500
// bl DELAYTC
b loop // Jump to loop
INIT_TC_PSP:
push {r0, r1, lr}
ldr r1, =SCS
ldr r0, =SYSTICK_RELOAD_1MS
str r0, [r1, #SCS_SYST_RVR]
ldr r0, =0
str r0, [r1, #SCS_SYST_CVR]
ldr r0, =7 // TickINT Bit also set to 1
str r0, [r1, #SCS_SYST_CSR]
pop {r0, r1, pc}
.global SysTick_Handler
.type SysTick_Handler, %function
SysTick_Handler:
push {r3, r4, r5, r6, lr}
// adr r3,LEDSTAT
// ldr r4,[r3]
// cmp r4,#0
add r8,r8,#1
cmp r8,#500
blo RET
mov r8,#0 // reset ms counter
cmp r7,#0 // check flag
beq LOFF
mov r5, #LEDs_OFF
// mov r4,#0
// str r4,[r3]
mov r7,#0
b CONT
LOFF: mov r5, #LEDs_ON
// mov r4,#0xff
mov r7,#0xff
str r4,[r3]
CONT:
// Set GPIOD Pins through BSSR register
ldr r6, =GPIOD_BASE // Load GPIOD BASE address to r6
str r5, [r6,#GPIOD_BSSR] // Write to BSRR register
RET: pop {r3, r4, r5, r6, pc}
// bx lr
Default_Handler:
Infinite_Loop:
b Infinite_Loop
INIT_TC:
push {r0, r1, lr}
ldr r1, =SCS
ldr r0, =SYSTICK_RELOAD_1MS
str r0, [r1, #SCS_SYST_RVR]
ldr r0, =0
str r0, [r1, #SCS_SYST_CVR]
ldr r0, =5
str r0, [r1, #SCS_SYST_CSR]
pop {r0, r1, pc}
INIT_IO:
push {r5, r6, lr}
// Enable GPIOD Peripheral Clock (bit 3 in AHB1ENR register)
ldr r6, = RCC_AHB1ENR // Load peripheral clock reg address to r6
ldr r5, [r6] // Read its content to r5
orr r5, 0x00000008 // Set bit 3 to enable GPIOD clock
str r5, [r6] // Store result in peripheral clock register
// Make GPIOD Pin12 as output pin (bits 25:24 in MODER register)
ldr r6, =GPIOD_BASE // Load GPIOD BASE address to r6
ldr r5, [r6,#GPIOD_MODER] // Read GPIOD_MODER content to r5
and r5, 0x00FFFFFF // Clear bits 31-24 for P12-15
orr r5, 0x55000000 // Write 01 to bits 31-24 for P12-15
str r5, [r6] // Store result in GPIOD MODER register
pop {r5, r6, pc}
LED_ON:
push {r5, r6, lr}
// Set GPIOD Pins to 1 (through BSSR register)
ldr r6, =GPIOD_BASE // Load GPIOD BASE address to r6
mov r5, #LEDs_ON
str r5, [r6,#GPIOD_BSSR] // Write to BSRR register
pop {r5, r6, pc}
LED_OFF:
push {r5, r6, lr}
// Set GPIOD Pins to 0 (through BSSR register)
ldr r6, =GPIOD_BASE // Load GPIOD BASE address to r6
mov r5, #LEDs_OFF
str r5, [r6,#GPIOD_BSSR] // Write to BSRR register
pop {r5, r6, pc}
DELAYTC:
push {r1, r2, lr}
ldr r1, =SCS
LOOPTC: ldr r2, [r1, #SCS_SYST_CSR]
tst r2, #0x10000
beq LOOPTC
subs r0, r0, 1
bne LOOPTC
pop {r1, r2, pc}
DELAY:
push {r1, lr}
MSEC: ldr r1,=LEDDELAY
LOOP: subs r1, r1, 1
bne LOOP
subs r0, r0, 1
bne MSEC
pop {r1, pc}
//
// Based on: https://github.com/fcayci/stm32f4-assembly
//
// Turns on an LED attached to GPIOD Pin 12
// We need to enable the clock for GPIOD and set up pin 12 as output.
//
// We also measure delay by using SysTick Timer, coresponding code is included
//
// Start with enabling thumb 32 mode since Cortex-M4 do not work with arm mode
// Unified syntax is used to enable good of the both words...
// Make sure to run arm-none-eabi-objdump.exe -d prj1.elf to check if
// the assembler used proper instructions. (Like ADDS)
.thumb
.syntax unified
.cpu cortex-m4
//.arch armv7e-m
///////////////////////////////////////////////////////////////////////////////
// Definitions
///////////////////////////////////////////////////////////////////////////////
// Definitions section. Define all the registers and
// constants here for code readability.
// Constants
.equ LEDDELAY, 4000
// By default 16MHz internal HSI clock is enabled
// Internal loop takes 4 cycles
// Register Addresses
// You can find the base addresses for all peripherals from Memory Map section
// RM0090 on page 64. Then the offsets can be found on their relevant sections.
// RCC base address is 0x40023800
// AHB1ENR register offset is 0x30
.equ RCC_AHB1ENR, 0x40023830 // RCC AHB1 peripheral clock reg (page 180)
// GPIOD base address is 0x40020C00
.equ GPIOD_BASE, 0x40020C00 // GPIOD base address)
// MODER register offset is 0x00
.equ GPIOD_MODER, 0x00 // GPIOD port mode register (page 281)
// ODR register offset is 0x14
.equ GPIOD_ODR, 0x14 // GPIOD output data register (page 283)
// BSSR register offset is 0x18
.equ GPIOD_BSSR, 0x18 // GPIOD port set/reset register (page 284)
//Absolute addresses
// .equ GPIOD_MODER, 0x40020C00 // GPIOD port mode register (page 281)
// .equ GPIOD_ODR, 0x40020C14 // GPIOD output data register (page 283)
// .equ GPIOD_BSSR, 0x40020C18 // GPIOD port set/reset register (page 284)
// SysTick Timer definitions
.equ SCS, 0xe000e000
.equ SCS_SYST_CSR, 0x10 // Control/Status register
.equ SCS_SYST_RVR, 0x14 // Value to countdown from
.equ SCS_SYST_CVR, 0x18 // Current value
.equ SYSTICK_RELOAD_1MS, 15999 //1 msec at 16MHz ... 16 000 000 / 500 - 1
// Values for BSSR register - pin 12
.equ LEDs_ON, 0x0000F000
.equ LEDs_OFF, 0xF0000000
@ -- Zero initialized data ---
.section .data
LEDSTAT: .word 0
// Start of text section
.section .text
///////////////////////////////////////////////////////////////////////////////
// Vectors
///////////////////////////////////////////////////////////////////////////////
// Vector table start
// Add all other processor specific exceptions/interrupts in order here
.long __StackTop // Top of the stack. from linker script
.long _start +1 // reset location, +1 for thumb mode
.word NMI_Handler
.word HardFault_Handler
.word MemManage_Handler
.word BusFault_Handler
.word UsageFault_Handler
.word 0
.word 0
.word 0
.word 0
.word SVC_Handler
.word DebugMon_Handler
.word 0
.word PendSV_Handler
.word SysTick_Handler
/* External Interrupts */
.word WWDG_IRQHandler /* Window WatchDog */
.word PVD_IRQHandler /* PVD through EXTI Line detection */
.word TAMP_STAMP_IRQHandler /* Tamper and TimeStamps through the EXTI line */
.word RTC_WKUP_IRQHandler /* RTC Wakeup through the EXTI line */
.word FLASH_IRQHandler /* FLASH */
.word RCC_IRQHandler /* RCC */
.word EXTI0_IRQHandler /* EXTI Line0 */
.word EXTI1_IRQHandler /* EXTI Line1 */
.word EXTI2_IRQHandler /* EXTI Line2 */
.word EXTI3_IRQHandler /* EXTI Line3 */
.word EXTI4_IRQHandler /* EXTI Line4 */
.word DMA1_Stream0_IRQHandler /* DMA1 Stream 0 */
.word DMA1_Stream1_IRQHandler /* DMA1 Stream 1 */
.word DMA1_Stream2_IRQHandler /* DMA1 Stream 2 */
.word DMA1_Stream3_IRQHandler /* DMA1 Stream 3 */
.word DMA1_Stream4_IRQHandler /* DMA1 Stream 4 */
.word DMA1_Stream5_IRQHandler /* DMA1 Stream 5 */
.word DMA1_Stream6_IRQHandler /* DMA1 Stream 6 */
.word ADC_IRQHandler /* ADC1, ADC2 and ADC3s */
.word CAN1_TX_IRQHandler /* CAN1 TX */
.word CAN1_RX0_IRQHandler /* CAN1 RX0 */
.word CAN1_RX1_IRQHandler /* CAN1 RX1 */
.word CAN1_SCE_IRQHandler /* CAN1 SCE */
.word EXTI9_5_IRQHandler /* External Line[9:5]s */
.word TIM1_BRK_TIM9_IRQHandler /* TIM1 Break and TIM9 */
.word TIM1_UP_TIM10_IRQHandler /* TIM1 Update and TIM10 */
.word TIM1_TRG_COM_TIM11_IRQHandler /* TIM1 Trigger and Commutation and TIM11 */
.word TIM1_CC_IRQHandler /* TIM1 Capture Compare */
.word TIM2_IRQHandler /* TIM2 */
.word TIM3_IRQHandler /* TIM3 */
.word TIM4_IRQHandler /* TIM4 */
.word I2C1_EV_IRQHandler /* I2C1 Event */
.word I2C1_ER_IRQHandler /* I2C1 Error */
.word I2C2_EV_IRQHandler /* I2C2 Event */
.word I2C2_ER_IRQHandler /* I2C2 Error */
.word SPI1_IRQHandler /* SPI1 */
.word SPI2_IRQHandler /* SPI2 */
.word USART1_IRQHandler /* USART1 */
.word USART2_IRQHandler /* USART2 */
.word USART3_IRQHandler /* USART3 */
.word EXTI15_10_IRQHandler /* External Line[15:10]s */
.word RTC_Alarm_IRQHandler /* RTC Alarm (A and B) through EXTI Line */
.word OTG_FS_WKUP_IRQHandler /* USB OTG FS Wakeup through EXTI line */
.word TIM8_BRK_TIM12_IRQHandler /* TIM8 Break and TIM12 */
.word TIM8_UP_TIM13_IRQHandler /* TIM8 Update and TIM13 */
.word TIM8_TRG_COM_TIM14_IRQHandler /* TIM8 Trigger and Commutation and TIM14 */
.word TIM8_CC_IRQHandler /* TIM8 Capture Compare */
.word DMA1_Stream7_IRQHandler /* DMA1 Stream7 */
.word FSMC_IRQHandler /* FSMC */
.word SDIO_IRQHandler /* SDIO */
.word TIM5_IRQHandler /* TIM5 */
.word SPI3_IRQHandler /* SPI3 */
.word UART4_IRQHandler /* UART4 */
.word UART5_IRQHandler /* UART5 */
.word TIM6_DAC_IRQHandler /* TIM6 and DAC1&2 underrun errors */
.word TIM7_IRQHandler /* TIM7 */
.word DMA2_Stream0_IRQHandler /* DMA2 Stream 0 */
.word DMA2_Stream1_IRQHandler /* DMA2 Stream 1 */
.word DMA2_Stream2_IRQHandler /* DMA2 Stream 2 */
.word DMA2_Stream3_IRQHandler /* DMA2 Stream 3 */
.word DMA2_Stream4_IRQHandler /* DMA2 Stream 4 */
.word ETH_IRQHandler /* Ethernet */
.word ETH_WKUP_IRQHandler /* Ethernet Wakeup through EXTI line */
.word CAN2_TX_IRQHandler /* CAN2 TX */
.word CAN2_RX0_IRQHandler /* CAN2 RX0 */
.word CAN2_RX1_IRQHandler /* CAN2 RX1 */
.word CAN2_SCE_IRQHandler /* CAN2 SCE */
.word OTG_FS_IRQHandler /* USB OTG FS */
.word DMA2_Stream5_IRQHandler /* DMA2 Stream 5 */
.word DMA2_Stream6_IRQHandler /* DMA2 Stream 6 */
.word DMA2_Stream7_IRQHandler /* DMA2 Stream 7 */
.word USART6_IRQHandler /* USART6 */
.word I2C3_EV_IRQHandler /* I2C3 event */
.word I2C3_ER_IRQHandler /* I2C3 error */
.word OTG_HS_EP1_OUT_IRQHandler /* USB OTG HS End Point 1 Out */
.word OTG_HS_EP1_IN_IRQHandler /* USB OTG HS End Point 1 In */
.word OTG_HS_WKUP_IRQHandler /* USB OTG HS Wakeup through EXTI */
.word OTG_HS_IRQHandler /* USB OTG HS */
.word DCMI_IRQHandler /* DCMI */
.word 0 /* CRYP crypto */
.word HASH_RNG_IRQHandler /* Hash and Rng */
.word FPU_IRQHandler /* FPU */
/*******************************************************************************
*
* Provide weak aliases for each Exception handler to the Default_Handler.
* As they are weak aliases, any function with the same name will override
* this definition.
*
*******************************************************************************/
.weak NMI_Handler
.thumb_set NMI_Handler,Default_Handler
.weak HardFault_Handler
.thumb_set HardFault_Handler,Default_Handler
.weak MemManage_Handler
.thumb_set MemManage_Handler,Default_Handler
.weak BusFault_Handler
.thumb_set BusFault_Handler,Default_Handler
.weak UsageFault_Handler
.thumb_set UsageFault_Handler,Default_Handler
.weak SVC_Handler
.thumb_set SVC_Handler,Default_Handler
.weak DebugMon_Handler
.thumb_set DebugMon_Handler,Default_Handler
.weak PendSV_Handler
.thumb_set PendSV_Handler,Default_Handler
.weak SysTick_Handler
// .thumb_set SysTick_Handler,Default_Handler
.weak WWDG_IRQHandler
.thumb_set WWDG_IRQHandler,Default_Handler
.weak PVD_IRQHandler
.thumb_set PVD_IRQHandler,Default_Handler
.weak TAMP_STAMP_IRQHandler
.thumb_set TAMP_STAMP_IRQHandler,Default_Handler
.weak RTC_WKUP_IRQHandler
.thumb_set RTC_WKUP_IRQHandler,Default_Handler
.weak FLASH_IRQHandler
.thumb_set FLASH_IRQHandler,Default_Handler
.weak RCC_IRQHandler
.thumb_set RCC_IRQHandler,Default_Handler
.weak EXTI0_IRQHandler
.thumb_set EXTI0_IRQHandler,Default_Handler
.weak EXTI1_IRQHandler
.thumb_set EXTI1_IRQHandler,Default_Handler
.weak EXTI2_IRQHandler
.thumb_set EXTI2_IRQHandler,Default_Handler
.weak EXTI3_IRQHandler
.thumb_set EXTI3_IRQHandler,Default_Handler
.weak EXTI4_IRQHandler
.thumb_set EXTI4_IRQHandler,Default_Handler
.weak DMA1_Stream0_IRQHandler
.thumb_set DMA1_Stream0_IRQHandler,Default_Handler
.weak DMA1_Stream1_IRQHandler
.thumb_set DMA1_Stream1_IRQHandler,Default_Handler
.weak DMA1_Stream2_IRQHandler
.thumb_set DMA1_Stream2_IRQHandler,Default_Handler
.weak DMA1_Stream3_IRQHandler
.thumb_set DMA1_Stream3_IRQHandler,Default_Handler
.weak DMA1_Stream4_IRQHandler
.thumb_set DMA1_Stream4_IRQHandler,Default_Handler
.weak DMA1_Stream5_IRQHandler
.thumb_set DMA1_Stream5_IRQHandler,Default_Handler
.weak DMA1_Stream6_IRQHandler
.thumb_set DMA1_Stream6_IRQHandler,Default_Handler
.weak ADC_IRQHandler
.thumb_set ADC_IRQHandler,Default_Handler
.weak CAN1_TX_IRQHandler
.thumb_set CAN1_TX_IRQHandler,Default_Handler
.weak CAN1_RX0_IRQHandler
.thumb_set CAN1_RX0_IRQHandler,Default_Handler
.weak CAN1_RX1_IRQHandler
.thumb_set CAN1_RX1_IRQHandler,Default_Handler
.weak CAN1_SCE_IRQHandler
.thumb_set CAN1_SCE_IRQHandler,Default_Handler
.weak EXTI9_5_IRQHandler
.thumb_set EXTI9_5_IRQHandler,Default_Handler
.weak TIM1_BRK_TIM9_IRQHandler
.thumb_set TIM1_BRK_TIM9_IRQHandler,Default_Handler
.weak TIM1_UP_TIM10_IRQHandler
.thumb_set TIM1_UP_TIM10_IRQHandler,Default_Handler
.weak TIM1_TRG_COM_TIM11_IRQHandler
.thumb_set TIM1_TRG_COM_TIM11_IRQHandler,Default_Handler
.weak TIM1_CC_IRQHandler
.thumb_set TIM1_CC_IRQHandler,Default_Handler
.weak TIM2_IRQHandler
.thumb_set TIM2_IRQHandler,Default_Handler
.weak TIM3_IRQHandler
.thumb_set TIM3_IRQHandler,Default_Handler
.weak TIM4_IRQHandler
.thumb_set TIM4_IRQHandler,Default_Handler
.weak I2C1_EV_IRQHandler
.thumb_set I2C1_EV_IRQHandler,Default_Handler
.weak I2C1_ER_IRQHandler
.thumb_set I2C1_ER_IRQHandler,Default_Handler
.weak I2C2_EV_IRQHandler
.thumb_set I2C2_EV_IRQHandler,Default_Handler
.weak I2C2_ER_IRQHandler
.thumb_set I2C2_ER_IRQHandler,Default_Handler
.weak SPI1_IRQHandler
.thumb_set SPI1_IRQHandler,Default_Handler
.weak SPI2_IRQHandler
.thumb_set SPI2_IRQHandler,Default_Handler
.weak USART1_IRQHandler
.thumb_set USART1_IRQHandler,Default_Handler
.weak USART2_IRQHandler
.thumb_set USART2_IRQHandler,Default_Handler
.weak USART3_IRQHandler
.thumb_set USART3_IRQHandler,Default_Handler
.weak EXTI15_10_IRQHandler
.thumb_set EXTI15_10_IRQHandler,Default_Handler
.weak RTC_Alarm_IRQHandler
.thumb_set RTC_Alarm_IRQHandler,Default_Handler
.weak OTG_FS_WKUP_IRQHandler
.thumb_set OTG_FS_WKUP_IRQHandler,Default_Handler
.weak TIM8_BRK_TIM12_IRQHandler
.thumb_set TIM8_BRK_TIM12_IRQHandler,Default_Handler
.weak TIM8_UP_TIM13_IRQHandler
.thumb_set TIM8_UP_TIM13_IRQHandler,Default_Handler
.weak TIM8_TRG_COM_TIM14_IRQHandler
.thumb_set TIM8_TRG_COM_TIM14_IRQHandler,Default_Handler
.weak TIM8_CC_IRQHandler
.thumb_set TIM8_CC_IRQHandler,Default_Handler
.weak DMA1_Stream7_IRQHandler
.thumb_set DMA1_Stream7_IRQHandler,Default_Handler
.weak FSMC_IRQHandler
.thumb_set FSMC_IRQHandler,Default_Handler
.weak SDIO_IRQHandler
.thumb_set SDIO_IRQHandler,Default_Handler
.weak TIM5_IRQHandler
.thumb_set TIM5_IRQHandler,Default_Handler
.weak SPI3_IRQHandler
.thumb_set SPI3_IRQHandler,Default_Handler
.weak UART4_IRQHandler
.thumb_set UART4_IRQHandler,Default_Handler
.weak UART5_IRQHandler
.thumb_set UART5_IRQHandler,Default_Handler
.weak TIM6_DAC_IRQHandler
.thumb_set TIM6_DAC_IRQHandler,Default_Handler
.weak TIM7_IRQHandler
.thumb_set TIM7_IRQHandler,Default_Handler
.weak DMA2_Stream0_IRQHandler
.thumb_set DMA2_Stream0_IRQHandler,Default_Handler
.weak DMA2_Stream1_IRQHandler
.thumb_set DMA2_Stream1_IRQHandler,Default_Handler
.weak DMA2_Stream2_IRQHandler
.thumb_set DMA2_Stream2_IRQHandler,Default_Handler
.weak DMA2_Stream3_IRQHandler
.thumb_set DMA2_Stream3_IRQHandler,Default_Handler
.weak DMA2_Stream4_IRQHandler
.thumb_set DMA2_Stream4_IRQHandler,Default_Handler
.weak ETH_IRQHandler
.thumb_set ETH_IRQHandler,Default_Handler
.weak ETH_WKUP_IRQHandler
.thumb_set ETH_WKUP_IRQHandler,Default_Handler
.weak CAN2_TX_IRQHandler
.thumb_set CAN2_TX_IRQHandler,Default_Handler
.weak CAN2_RX0_IRQHandler
.thumb_set CAN2_RX0_IRQHandler,Default_Handler
.weak CAN2_RX1_IRQHandler
.thumb_set CAN2_RX1_IRQHandler,Default_Handler
.weak CAN2_SCE_IRQHandler
.thumb_set CAN2_SCE_IRQHandler,Default_Handler
.weak OTG_FS_IRQHandler
.thumb_set OTG_FS_IRQHandler,Default_Handler
.weak DMA2_Stream5_IRQHandler
.thumb_set DMA2_Stream5_IRQHandler,Default_Handler
.weak DMA2_Stream6_IRQHandler
.thumb_set DMA2_Stream6_IRQHandler,Default_Handler
.weak DMA2_Stream7_IRQHandler
.thumb_set DMA2_Stream7_IRQHandler,Default_Handler
.weak USART6_IRQHandler
.thumb_set USART6_IRQHandler,Default_Handler
.weak I2C3_EV_IRQHandler
.thumb_set I2C3_EV_IRQHandler,Default_Handler
.weak I2C3_ER_IRQHandler
.thumb_set I2C3_ER_IRQHandler,Default_Handler
.weak OTG_HS_EP1_OUT_IRQHandler
.thumb_set OTG_HS_EP1_OUT_IRQHandler,Default_Handler
.weak OTG_HS_EP1_IN_IRQHandler
.thumb_set OTG_HS_EP1_IN_IRQHandler,Default_Handler
.weak OTG_HS_WKUP_IRQHandler
.thumb_set OTG_HS_WKUP_IRQHandler,Default_Handler
.weak OTG_HS_IRQHandler
.thumb_set OTG_HS_IRQHandler,Default_Handler
.weak DCMI_IRQHandler
.thumb_set DCMI_IRQHandler,Default_Handler
.weak HASH_RNG_IRQHandler
.thumb_set HASH_RNG_IRQHandler,Default_Handler
.weak FPU_IRQHandler
.thumb_set FPU_IRQHandler,Default_Handler
///////////////////////////////////////////////////////////////////////////////
// Main code starts from here
///////////////////////////////////////////////////////////////////////////////
_start:
bl INIT_IO
mov r8,#0 // Clear ms counter
bl INIT_TC_PSP
loop:
// bl LED_ON
// mov r0, 500
// bl DELAYTC
// bl LED_OFF
// mov r0, 500
// bl DELAYTC
b loop // Jump to loop
INIT_TC_PSP:
push {r0, r1, lr}
ldr r1, =SCS
ldr r0, =SYSTICK_RELOAD_1MS
str r0, [r1, #SCS_SYST_RVR]
ldr r0, =0
str r0, [r1, #SCS_SYST_CVR]
ldr r0, =7 // TickINT Bit also set to 1
str r0, [r1, #SCS_SYST_CSR]
pop {r0, r1, pc}
.global SysTick_Handler
.type SysTick_Handler, %function
SysTick_Handler:
push {r3, r4, r5, r6, lr}
// adr r3,LEDSTAT
// ldr r4,[r3]
// cmp r4,#0
add r8,r8,#1
cmp r8,#500
blo RET
mov r8,#0 // reset ms counter
cmp r7,#0 // check flag
beq LOFF
mov r5, #LEDs_OFF
// mov r4,#0
// str r4,[r3]
mov r7,#0
b CONT
LOFF: mov r5, #LEDs_ON
// mov r4,#0xff
mov r7,#0xff
str r4,[r3]
CONT:
// Set GPIOD Pins through BSSR register
ldr r6, =GPIOD_BASE // Load GPIOD BASE address to r6
str r5, [r6,#GPIOD_BSSR] // Write to BSRR register
RET: pop {r3, r4, r5, r6, pc}
// bx lr
Default_Handler:
Infinite_Loop:
b Infinite_Loop
INIT_TC:
push {r0, r1, lr}
ldr r1, =SCS
ldr r0, =SYSTICK_RELOAD_1MS
str r0, [r1, #SCS_SYST_RVR]
ldr r0, =0
str r0, [r1, #SCS_SYST_CVR]
ldr r0, =5
str r0, [r1, #SCS_SYST_CSR]
pop {r0, r1, pc}
INIT_IO:
push {r5, r6, lr}
// Enable GPIOD Peripheral Clock (bit 3 in AHB1ENR register)
ldr r6, = RCC_AHB1ENR // Load peripheral clock reg address to r6
ldr r5, [r6] // Read its content to r5
orr r5, 0x00000008 // Set bit 3 to enable GPIOD clock
str r5, [r6] // Store result in peripheral clock register
// Make GPIOD Pin12 as output pin (bits 25:24 in MODER register)
ldr r6, =GPIOD_BASE // Load GPIOD BASE address to r6
ldr r5, [r6,#GPIOD_MODER] // Read GPIOD_MODER content to r5
and r5, 0x00FFFFFF // Clear bits 31-24 for P12-15
orr r5, 0x55000000 // Write 01 to bits 31-24 for P12-15
str r5, [r6] // Store result in GPIOD MODER register
pop {r5, r6, pc}
LED_ON:
push {r5, r6, lr}
// Set GPIOD Pins to 1 (through BSSR register)
ldr r6, =GPIOD_BASE // Load GPIOD BASE address to r6
mov r5, #LEDs_ON
str r5, [r6,#GPIOD_BSSR] // Write to BSRR register
pop {r5, r6, pc}
LED_OFF:
push {r5, r6, lr}
// Set GPIOD Pins to 0 (through BSSR register)
ldr r6, =GPIOD_BASE // Load GPIOD BASE address to r6
mov r5, #LEDs_OFF
str r5, [r6,#GPIOD_BSSR] // Write to BSRR register
pop {r5, r6, pc}
DELAYTC:
push {r1, r2, lr}
ldr r1, =SCS
LOOPTC: ldr r2, [r1, #SCS_SYST_CSR]
tst r2, #0x10000
beq LOOPTC
subs r0, r0, 1
bne LOOPTC
pop {r1, r2, pc}
DELAY:
push {r1, lr}
MSEC: ldr r1,=LEDDELAY
LOOP: subs r1, r1, 1
bne LOOP
subs r0, r0, 1
bne MSEC
pop {r1, pc}
Last modified: Sunday, 8 January 2023, 11:09 PM