STM32F4 rešitve
// STM32F4 Discovery - Assembly template for CO LAB course
//
// Based on: https://github.com/fcayci/stm32f4-assembly
//
// Initializes USART2 device for single char transmit/receive
// Single char is sent on TX and, if loopback wire is installed (PD5-PD6), char is received on RX channel
// LED blinks on 0.5 secs, when TX and RX are working ok.
// Start with enabling thumb 32 mode since Cortex-M4 do not work with arm mode
// Unified syntax is used to enable good of the both words...
// Make sure to run arm-none-eabi-objdump.exe -d prj1.elf to check if
// the assembler used proper instructions. (Like ADDS)
.thumb
.syntax unified
.cpu cortex-m4
//.arch armv7e-m
///////////////////////////////////////////////////////////////////////////////
// Definitions
///////////////////////////////////////////////////////////////////////////////
// Definitions section. Define all the registers and
// constants here for code readability.
// Constants
.equ LEDDELAY, 4000
// By default 16MHz internal HSI clock is enabled
// Internal loop takes 4 cycles
// Register Addresses
// You can find the base addresses for all peripherals from Memory Map section
// RM0090 on page 64. Then the offsets can be found on their relevant sections.
// RCC base address is 0x40023800
.equ RCC_BASE, 0x40023800 // RCC AHB1 peripheral clock reg (page 180)
// AHB1ENR register offset is 0x30
.equ RCC_AHB1ENR, 0x30 // RCC AHB1 peripheral clock reg (page 180)
// APB1ENR register offset is 0x30
.equ RCC_APB1ENR, 0x40 // RCC APB1 peripheral clock reg (page 183)
// GPIOD base address is 0x40020C00
.equ GPIOD_BASE, 0x40020C00 // GPIOD base address)
// MODER register offset is 0x00
.equ GPIOD_MODER, 0x00 // GPIOD port mode register (page 281)
// ODR register offset is 0x14
.equ GPIOD_ODR, 0x14 // GPIOD output data register (page 283)
// BSSR register offset is 0x18
.equ GPIOD_BSSR, 0x18 // GPIOD port set/reset register (page 284)
// AFRL register offset is 0x20
.equ GPIOD_AFRL, 0x20 // GPIOD output data register (page 285)
.equ GPIOD_AFRL_VALUE, 0x07700000 // AF7 on PD5,6
//Absolute addresses
// .equ GPIOD_MODER, 0x40020C00 // GPIOD port mode register (page 281)
// .equ GPIOD_ODR, 0x40020C14 // GPIOD output data register (page 283)
// .equ GPIOD_BSSR, 0x40020C18 // GPIOD port set/reset register (page 284)
// USART2 base address is 0x40004400
.equ USART2_BASE, 0x40004400 // USART2 base address)
// SR register
.equ USART2_SR, 0x00 // SR register (page 1007)
// DR register
.equ USART2_DR, 0x04 // SR register (page 1007)
// BRR register
.equ USART2_BRR, 0x08 // BRR register (page 1010)
.equ USART2_BRR_VAL, (52<<4)+0b0001 // BRR register
// CR1 register
.equ USART2_CR1, 0x0C // CR1 register
.equ USART2_CR1_VAL, 0x200C // CR1 register
// SysTick Timer definitions
.equ SCS, 0xe000e000
.equ SCS_SYST_CSR, 0x10 // Control/Status register
.equ SCS_SYST_RVR, 0x14 // Value to countdown from
.equ SCS_SYST_CVR, 0x18 // Current value
.equ SYSTICK_RELOAD_1MS, 15999 //1 msec at 16MHz ... 16 000 000 / 500 - 1
// Values for BSSR register - pin 12
.equ LEDs_ON, 0x0000F000
.equ LEDs_OFF, 0xF0000000
// Start of text section
.section .text
///////////////////////////////////////////////////////////////////////////////
// Vectors
///////////////////////////////////////////////////////////////////////////////
// Vector table start
// Add all other processor specific exceptions/interrupts in order here
.long __StackTop // Top of the stack. from linker script
.long _start +1 // reset location, +1 for thumb mode
///////////////////////////////////////////////////////////////////////////////
// Main code starts from here
///////////////////////////////////////////////////////////////////////////////
_start:
bl INIT_IO
bl INIT_UART
bl INIT_TC
loop:
mov r0,#'a'
bl SEND_UART
bl LED_OFF
mov r0, 500
bl DELAYTC
bl RECV_UART
bl LED_ON
mov r0, 500
bl DELAYTC
b loop // Jump to loop
INIT_UART:
push {r5, r6, lr}
// Enable USART2 Peripheral Clock (bit 17 in APB1ENR register)
ldr r6, =RCC_BASE // Load peripheral clock reg base address to r6
ldr r5, [r6,#RCC_APB1ENR] // Read its content to r5
orr r5, #(1<<17) // Set bit 17 to enable USART2 clock
str r5, [r6,#RCC_APB1ENR] // Store result in peripheral clock register
ldr r6, =GPIOD_BASE // Load GPIOD BASE address to r6
// Make GPIOD Pina 5,6 as AF7 (bits 20:27 in AFRL register)
ldr r5, [r6,#GPIOD_AFRL] // Read GPIOD_AFRL content to r5
and r5, 0x0FF00000
orr r5, GPIOD_AFRL_VALUE
str r5, [r6,#GPIOD_AFRL] // Store result in GPIOD AFRL register
// Make GPIOD Pins 5,6 as AF (bits 10:13 in MODER register)
ldr r5, [r6,#GPIOD_MODER] // Read GPIOD_MODER content to r5
and r5, 0xFFFFC3FF // Clear bits
orr r5, 0x00002800 // Write 0b10 to bits
str r5, [r6,#GPIOD_MODER] // Store result in GPIOD MODER register
ldr r6, =USART2_BASE // Load USART2 BASE address to r6
// Set USART2 BaudRate
ldr r5, =USART2_BRR_VAL
str r5, [r6,#USART2_BRR] // Store result in GPIOD MODER register
// Start USART2
ldr r5, =USART2_CR1_VAL
str r5, [r6,#USART2_CR1] // Store result in GPIOD MODER register
pop {r5, r6, pc}
RECV_UART:
push {r1, r2, lr}
ldr r1, =USART2_BASE
RECV_LP:
ldr r2, [r1, #USART2_SR]
tst r2, #(1 << 5)
beq RECV_LP
ldr r0, [r1, #USART2_DR]
pop {r1, r2, pc}
SEND_UART:
push {r1, r2, lr}
ldr r1, =USART2_BASE
SEND_LP:
ldr r2, [r1, #USART2_SR]
tst r2, #(1 << 7)
beq SEND_LP
str r0, [r1, #USART2_DR]
pop {r1, r2, pc}
INIT_TC:
push {r0, r1, lr}
ldr r1, =SCS
ldr r0, =SYSTICK_RELOAD_1MS
str r0, [r1, #SCS_SYST_RVR]
ldr r0, =0
str r0, [r1, #SCS_SYST_CVR]
ldr r0, =5
str r0, [r1, #SCS_SYST_CSR]
pop {r0, r1, pc}
INIT_IO:
push {r5, r6, lr}
// Enable GPIOD Peripheral Clock (bit 3 in AHB1ENR register)
ldr r6, = RCC_BASE // Load peripheral clock reg base address to r6
ldr r5, [r6,#RCC_AHB1ENR] // Read its content to r5
orr r5, 0x00000008 // Set bit 3 to enable GPIOD clock
str r5, [r6,#RCC_AHB1ENR] // Store result in peripheral clock register
// Make GPIOD Pin12 as output pin (bits 25:24 in MODER register)
ldr r6, =GPIOD_BASE // Load GPIOD BASE address to r6
ldr r5, [r6,#GPIOD_MODER] // Read GPIOD_MODER content to r5
and r5, 0x00FFFFFF // Clear bits 31-24 for P12-15
orr r5, 0x55000000 // Write 01 to bits 31-24 for P12-15
str r5, [r6] // Store result in GPIOD MODER register
pop {r5, r6, pc}
LED_ON:
push {r5, r6, lr}
// Set GPIOD Pins to 1 (through BSSR register)
ldr r6, =GPIOD_BASE // Load GPIOD BASE address to r6
mov r5, #LEDs_ON
str r5, [r6,#GPIOD_BSSR] // Write to BSRR register
pop {r5, r6, pc}
LED_OFF:
push {r5, r6, lr}
// Set GPIOD Pins to 0 (through BSSR register)
ldr r6, =GPIOD_BASE // Load GPIOD BASE address to r6
mov r5, #LEDs_OFF
str r5, [r6,#GPIOD_BSSR] // Write to BSRR register
pop {r5, r6, pc}
DELAYTC:
push {r1, r2, lr}
ldr r1, =SCS
LOOPTC: ldr r2, [r1, #SCS_SYST_CSR]
tst r2, #0x10000
beq LOOPTC
subs r0, r0, 1
bne LOOPTC
pop {r1, r2, pc}
DELAY:
push {r1, lr}
MSEC: ldr r1,=LEDDELAY
LOOP: subs r1, r1, 1
bne LOOP
subs r0, r0, 1
bne MSEC
pop {r1, pc}
//
// Based on: https://github.com/fcayci/stm32f4-assembly
//
// Initializes USART2 device for single char transmit/receive
// Single char is sent on TX and, if loopback wire is installed (PD5-PD6), char is received on RX channel
// LED blinks on 0.5 secs, when TX and RX are working ok.
// Start with enabling thumb 32 mode since Cortex-M4 do not work with arm mode
// Unified syntax is used to enable good of the both words...
// Make sure to run arm-none-eabi-objdump.exe -d prj1.elf to check if
// the assembler used proper instructions. (Like ADDS)
.thumb
.syntax unified
.cpu cortex-m4
//.arch armv7e-m
///////////////////////////////////////////////////////////////////////////////
// Definitions
///////////////////////////////////////////////////////////////////////////////
// Definitions section. Define all the registers and
// constants here for code readability.
// Constants
.equ LEDDELAY, 4000
// By default 16MHz internal HSI clock is enabled
// Internal loop takes 4 cycles
// Register Addresses
// You can find the base addresses for all peripherals from Memory Map section
// RM0090 on page 64. Then the offsets can be found on their relevant sections.
// RCC base address is 0x40023800
.equ RCC_BASE, 0x40023800 // RCC AHB1 peripheral clock reg (page 180)
// AHB1ENR register offset is 0x30
.equ RCC_AHB1ENR, 0x30 // RCC AHB1 peripheral clock reg (page 180)
// APB1ENR register offset is 0x30
.equ RCC_APB1ENR, 0x40 // RCC APB1 peripheral clock reg (page 183)
// GPIOD base address is 0x40020C00
.equ GPIOD_BASE, 0x40020C00 // GPIOD base address)
// MODER register offset is 0x00
.equ GPIOD_MODER, 0x00 // GPIOD port mode register (page 281)
// ODR register offset is 0x14
.equ GPIOD_ODR, 0x14 // GPIOD output data register (page 283)
// BSSR register offset is 0x18
.equ GPIOD_BSSR, 0x18 // GPIOD port set/reset register (page 284)
// AFRL register offset is 0x20
.equ GPIOD_AFRL, 0x20 // GPIOD output data register (page 285)
.equ GPIOD_AFRL_VALUE, 0x07700000 // AF7 on PD5,6
//Absolute addresses
// .equ GPIOD_MODER, 0x40020C00 // GPIOD port mode register (page 281)
// .equ GPIOD_ODR, 0x40020C14 // GPIOD output data register (page 283)
// .equ GPIOD_BSSR, 0x40020C18 // GPIOD port set/reset register (page 284)
// USART2 base address is 0x40004400
.equ USART2_BASE, 0x40004400 // USART2 base address)
// SR register
.equ USART2_SR, 0x00 // SR register (page 1007)
// DR register
.equ USART2_DR, 0x04 // SR register (page 1007)
// BRR register
.equ USART2_BRR, 0x08 // BRR register (page 1010)
.equ USART2_BRR_VAL, (52<<4)+0b0001 // BRR register
// CR1 register
.equ USART2_CR1, 0x0C // CR1 register
.equ USART2_CR1_VAL, 0x200C // CR1 register
// SysTick Timer definitions
.equ SCS, 0xe000e000
.equ SCS_SYST_CSR, 0x10 // Control/Status register
.equ SCS_SYST_RVR, 0x14 // Value to countdown from
.equ SCS_SYST_CVR, 0x18 // Current value
.equ SYSTICK_RELOAD_1MS, 15999 //1 msec at 16MHz ... 16 000 000 / 500 - 1
// Values for BSSR register - pin 12
.equ LEDs_ON, 0x0000F000
.equ LEDs_OFF, 0xF0000000
// Start of text section
.section .text
///////////////////////////////////////////////////////////////////////////////
// Vectors
///////////////////////////////////////////////////////////////////////////////
// Vector table start
// Add all other processor specific exceptions/interrupts in order here
.long __StackTop // Top of the stack. from linker script
.long _start +1 // reset location, +1 for thumb mode
///////////////////////////////////////////////////////////////////////////////
// Main code starts from here
///////////////////////////////////////////////////////////////////////////////
_start:
bl INIT_IO
bl INIT_UART
bl INIT_TC
loop:
mov r0,#'a'
bl SEND_UART
bl LED_OFF
mov r0, 500
bl DELAYTC
bl RECV_UART
bl LED_ON
mov r0, 500
bl DELAYTC
b loop // Jump to loop
INIT_UART:
push {r5, r6, lr}
// Enable USART2 Peripheral Clock (bit 17 in APB1ENR register)
ldr r6, =RCC_BASE // Load peripheral clock reg base address to r6
ldr r5, [r6,#RCC_APB1ENR] // Read its content to r5
orr r5, #(1<<17) // Set bit 17 to enable USART2 clock
str r5, [r6,#RCC_APB1ENR] // Store result in peripheral clock register
ldr r6, =GPIOD_BASE // Load GPIOD BASE address to r6
// Make GPIOD Pina 5,6 as AF7 (bits 20:27 in AFRL register)
ldr r5, [r6,#GPIOD_AFRL] // Read GPIOD_AFRL content to r5
and r5, 0x0FF00000
orr r5, GPIOD_AFRL_VALUE
str r5, [r6,#GPIOD_AFRL] // Store result in GPIOD AFRL register
// Make GPIOD Pins 5,6 as AF (bits 10:13 in MODER register)
ldr r5, [r6,#GPIOD_MODER] // Read GPIOD_MODER content to r5
and r5, 0xFFFFC3FF // Clear bits
orr r5, 0x00002800 // Write 0b10 to bits
str r5, [r6,#GPIOD_MODER] // Store result in GPIOD MODER register
ldr r6, =USART2_BASE // Load USART2 BASE address to r6
// Set USART2 BaudRate
ldr r5, =USART2_BRR_VAL
str r5, [r6,#USART2_BRR] // Store result in GPIOD MODER register
// Start USART2
ldr r5, =USART2_CR1_VAL
str r5, [r6,#USART2_CR1] // Store result in GPIOD MODER register
pop {r5, r6, pc}
RECV_UART:
push {r1, r2, lr}
ldr r1, =USART2_BASE
RECV_LP:
ldr r2, [r1, #USART2_SR]
tst r2, #(1 << 5)
beq RECV_LP
ldr r0, [r1, #USART2_DR]
pop {r1, r2, pc}
SEND_UART:
push {r1, r2, lr}
ldr r1, =USART2_BASE
SEND_LP:
ldr r2, [r1, #USART2_SR]
tst r2, #(1 << 7)
beq SEND_LP
str r0, [r1, #USART2_DR]
pop {r1, r2, pc}
INIT_TC:
push {r0, r1, lr}
ldr r1, =SCS
ldr r0, =SYSTICK_RELOAD_1MS
str r0, [r1, #SCS_SYST_RVR]
ldr r0, =0
str r0, [r1, #SCS_SYST_CVR]
ldr r0, =5
str r0, [r1, #SCS_SYST_CSR]
pop {r0, r1, pc}
INIT_IO:
push {r5, r6, lr}
// Enable GPIOD Peripheral Clock (bit 3 in AHB1ENR register)
ldr r6, = RCC_BASE // Load peripheral clock reg base address to r6
ldr r5, [r6,#RCC_AHB1ENR] // Read its content to r5
orr r5, 0x00000008 // Set bit 3 to enable GPIOD clock
str r5, [r6,#RCC_AHB1ENR] // Store result in peripheral clock register
// Make GPIOD Pin12 as output pin (bits 25:24 in MODER register)
ldr r6, =GPIOD_BASE // Load GPIOD BASE address to r6
ldr r5, [r6,#GPIOD_MODER] // Read GPIOD_MODER content to r5
and r5, 0x00FFFFFF // Clear bits 31-24 for P12-15
orr r5, 0x55000000 // Write 01 to bits 31-24 for P12-15
str r5, [r6] // Store result in GPIOD MODER register
pop {r5, r6, pc}
LED_ON:
push {r5, r6, lr}
// Set GPIOD Pins to 1 (through BSSR register)
ldr r6, =GPIOD_BASE // Load GPIOD BASE address to r6
mov r5, #LEDs_ON
str r5, [r6,#GPIOD_BSSR] // Write to BSRR register
pop {r5, r6, pc}
LED_OFF:
push {r5, r6, lr}
// Set GPIOD Pins to 0 (through BSSR register)
ldr r6, =GPIOD_BASE // Load GPIOD BASE address to r6
mov r5, #LEDs_OFF
str r5, [r6,#GPIOD_BSSR] // Write to BSRR register
pop {r5, r6, pc}
DELAYTC:
push {r1, r2, lr}
ldr r1, =SCS
LOOPTC: ldr r2, [r1, #SCS_SYST_CSR]
tst r2, #0x10000
beq LOOPTC
subs r0, r0, 1
bne LOOPTC
pop {r1, r2, pc}
DELAY:
push {r1, lr}
MSEC: ldr r1,=LEDDELAY
LOOP: subs r1, r1, 1
bne LOOP
subs r0, r0, 1
bne MSEC
pop {r1, pc}
Последнее изменение: понедельник, 27 марта 2023, 18:29